Victron Ultimate Caravan Off-Grid Bundle, 5 Year Warranty.
Bundle Includes:
- 2 x Victron LiFePO4 Lithium Battery 12.8V/200Ah-a – Smart, BAT512120610
- Victron MultiPlus-II Inverter Charger 12/3000/120-32, PMP122305010
- Victron Orion-Tr Smart 12/12-30A (360W) Non-isolated DC-DC charger, ORI121236140
- Victron Lynx Smart BMS 500, LYN034160200
- 2 x Victron Lynx Distributor, LYN060102000
- Victron Smart Battery Protect 12/24V-100A, BPR110022000
- Victron Cerbo GX, BPP900450100
- Victron GX Touch 50, BPP900455050
- Victron M8 Circular Connector Male/Female 3 Pole 2m, 2 Pack, ASS030560200
- 2 x Victron RJ45 UTP Cable 0.9m, ASS030064920
- Victron Interface MK3-USB – VE.Bus to USB., ASS030140000
2 x Victron LiFePO4 Lithium Battery 12.8V/200Ah-a – Smart
- With integrated cell balancing
- Can be parallel and series connected
- Bluetooth app available to monitor cell voltage and temperature
Why lithium-iron-phosphate?: Lithium-iron-phosphate (LiFePO4 or LFP) is the safest of the mainstream li-ion battery types. The nominal voltage of a LFP cell is 3,2V (lead-acid: 2V/cell). A 12,8V LFP battery therefore consists of 4 cells connected in series; and a 25,6V battery consists of 8 cells connected in series.
Bluetooth: With Bluetooth cell voltages, temperature and alarm status can be monitored. Very useful to localize a (potential) problem, such as cell imbalance.
Victron LFP batteries have integrated cell balancing and cell monitoring. Up to 5 batteries can be paralleled and up to four batteries can be series connected,so that a 48V battery bank of up to 1500Ah can be assembled. The cell balancing/monitoring cables can be daisychained and must be connected to a Battery Management System (BMS).
Battery Management System (BMS): The BMS will:
- Generate a pre-alarm whenever the voltage of a battery cell decreases to less than 3,1V (adjustable 2,85 – 3,15 V).
- Disconnect or shut down the load whenever the voltage of a battery cell decreases to less than 2,8V (adjustable 2,6 V – 2,8 V).
- Stop the charging process whenever the voltage of a battery cell increases to more than 3,75 V or the temperature increases to more than 60°C.
Victron MultiPlus-II Inverter Charger 12/3000/120-32
The MultiPlus-II combines the functions of the MultiPlus and the MultiGrid. It has all the features of the MultiPlus, plus an external current transformer option to implement PowerControl and PowerAssist and to optimize self-consumption with external current sensing (max. 32A). It also has all the features of the MultiGrid with built-in anti-islanding and an increasingly long list of country approvals.
PowerAssist:
The MultiPlus-II will prevent overload of a limited AC source, such as a generator or shore power connection. First, battery charging will automatically be reduced when otherwise an overload would occur. The second level will boost the output of a generator or shore side supply with power taken from the battery.
ESS: Energy Storage Systems:
The MultiPlus-II is the key component in a Victron ESS system, providing the flexibility to combine with MPPT Solar Chargers or Grid-tie PV Inverters. For examples and more detailed information see the ESS (Energy Storage System) manual.
Uninterrupted AC power (UPS function):
In the event of a grid failure, or when shore or generator power is disconnected, the inverter within the Multi is automatically activated and takes over the supply to the connected loads. This happens so fast (less than 20 milliseconds) that computers and other electronic equipment will continue to operate without disruption.
Remote Monitoring and Control:
Monitor and control your Multi and system or systems’ locally (LAN) or remotely via the internet from anywhere in the world, using the free VRM app and free VRM portal website. Access can be from a phone, tablet, laptop, or PC for multiple operating systems. There is no end to the level of control, via the required Color Control GX or Venus GX, from adjusting your Multi to auto-starting a back generator and more…
Victron Orion-Tr Smart 12/12-30A (360W) Non-isolated DC-DC charger.
The Orion-Tr Smart DC-DC charger is a professional DC to DC adaptive 3-stage charger with built-in Bluetooth.
For use in dual battery systems in vehicles or on boats where the alternator and the start battery are used to charge the service battery. The unit can be monitored and programmed via Bluetooth and can be remotely controlled via a remote on/off switch.
The Orion Tr-Smart charger can be used in 12V or 24V systems and is suitable for both lead-acid and lithium batteries. Models are available up to 400W and unlimited multiple units can be connected in parallel to increase output power. Suitable for high temperatures up to 55°C with a full rated output up to 40°C.
Bluetooth Smart enabled: Any Bluetooth enabled smartphone, tablet or other devices can be used to monitor, to change settings, and to update the charger when new software features become available.
Victron DC-DC Chargers: Non-Isolated vs Isolated: The main difference with an isolated DC-DC charger is the connection to each battery as there is only one negative connection to the battery. Plus, there is no internal connection between the negatives in the battery. Some systems require an isolated DC to DC charger, this can be some of the reasons:
- Typically, marine application with limited corrosion
- Decrease noise from one battery system that will affect another battery system
Either unit can be used for systems that don’t require isolation, but the non-isolated requires one less wire to be installed. One example of a non-isolated system is an automotive system, such as both batteries are negative and connected to the chassis of a vehicle. The system is non-isolated but either unit will suit.
No Solar Regulator in the DC-DC Charger: Victron have chosen to separate the charger and the solar regulators, these are the advantages:
- You can choose the correct solar regulator to match your panels with the best efficiency for the solar charging
- The solar can be charging into the battery system simultaneously with the onboard vehicle charging
- Without a solar regulator, the DC-DC charger will stay cheaper
Input fuse (not replaceable)
Victron Lynx Smart BMS 500
The Lynx Smart BMS is a dedicated Battery Management System for Victron Lithium Smart Batteries. There are multiple BMS-es available for our Smart Lithium series of batteries, and the Lynx Smart is the most feature rich and complete option. Its main features are:
- Built-in 500A contactor, used as a fall-back safety mechanism and also available as a remote controllable main systems switch
- Battery monitor, indicating state of charge percentage and more data.
- Pre-alarm signal: provide a warning before the system shuts down due to -for example- a low cell.
- Bluetooth for use withVictrons VictronConnect App, for setup and monitoring.
The Lynx Smart BMS is part of the modular Lynx Distribution system.
2 x Victron Lynx Distributor
A modular DC bus bar, with locations for four DC fuses. It will monitor the status of each fuse, and indicate its condition with a LED on the front. Part of the modular Lynx distribution system.
Victron Smart Battery Protect 12/24V-100A
The Smart BatteryProtect disconnects the battery from non-essential loads before it is completely discharged (which would damage the battery) or before it has insufficient power left to crank the engine.
When using Bluetooth to program the Smart BatteryProtect any required engage/disengage levels can be set. Alternatively, one of nine predefined engage/disengage levels can be set with the programming pin (see manual).
If required, Bluetooth can be disabled. The Smart BatteryProtect is a uni-directional device. It can only deal with current in one direction, so either current to a load, or current from a charger, but not both currents at the same time. In addition to this, current only can only flow from the IN terminal to the OUT terminal. In case of use with a load, the battery connects to the IN terminal, and in case of use with a charger, the charger connects to the IN terminal.
Victron Cerbo GX
Panels and system monitoring: This all-new communication-centre allows you to always have perfect control over your system from wherever you are and maximizes its performance. Simply connect through our Victron Remote Management (VRM) portal, or access directly, using the separate GX Touch 50, an MFD, or our VictronConnect app thanks to its added Bluetooth capability. This latest addition to the GX-range combines all the best of connectivity, redefining smart power solutions in every way.
Perfect monitoring & control: Instantly monitor the battery state of charge, power consumption, power harvest from PV, generator, and mains, or check tank levels and temperature measurements. Easily control the shore power input current limit, (auto)start/stop generator(s) or change any setting to optimize the system. Follow up on alerts, perform diagnostic checks, and resolve challenges remotely. The Cerbo GX turns any power challenge into an effortless experience.
Maximize your system performance: The Cerbo GX maximizes the performance of your system’s components in real-time and keeps them in perfect tune. With its Dual-Core Processor and the addition of an extra CAN-bus port you can now support even bigger systems; closely follow managed (lithium) batteries while the second port can support up to 25 simultaneously connected VE.Can solar chargers. The new NMEA 2000-out support has the GX easily integrated into any boat network. Four tank- and four temperature ports as well as 3 VE.Direct ports, 3 USB ports, 4 digital inputs, and 2 relays allow you to expand control to a new level. Maximizing systems’ performance was never this easy.
Simple mounting and configuration: The Cerbo GX is now optimized to more than meet the standards of installer professionals. The device is easily mountable on a DIN-Rail (with DIN35 adapter small, not included) and its separate touchscreen can now be bolted on top of a dashboard, eliminating the need to create perfect cut-outs (like with the Color Control GX) and is connected through just one cable, taking away the hassle of having to bring many wires to a dashboard. Its new Bluetooth feature enables a quick connection and configuration via our VictronConnect app.
Outsmart any power challenge: The Cerbo GX serves endless purposes, extending perfect control to the most diverse applications. For solutions including generators, such as Marine, or Backup & Off-grid, it will auto-start/stop your generator, or delays ignition until the end of ‘quiet’ periods. For Energy Storage Systems it keeps backup batteries at 100%, kicks-in during power-cuts, and diverts excess (solar) power to self-consumption, saving you money. For RV and Emergency vehicles it keeps vital systems function flawlessly. But that’s just to name a few…
Victron GX Touch 50
Panels and system monitoring: The GX Touch 50 is the display accessory for our Cerbo GX. The five-inch touch screen display gives an instant overview of your system and allows you to adjust settings in the blink of an eye. Simply connected to the Cerbo GX with one cable, its super slim waterproof design, top-mountable setup and its simple installation bring a lot of flexibility when creating a crisp and clean dashboard.
Simply mounted: The GX Touch is optimised to more than meet the standards of installer professionals. The screen is simply bolted on top of a dashboard, eliminating the need to create perfect cut-outs (like with the ColorControl GX) and is connected through just one cable, taking away the hassle of having to bring many wires to a dashboard.
The GX Touch 50 is a companion to the Cerbo GX, the all-new communication-centre allows you to always have perfect control over your system from wherever you are and maximises its performance. Simply connect through our Victron Remote Management (VRM) portal, or access directly, using the GX Touch 50, an MFD, or our VictronConnect app thanks to its added Bluetooth capability. This latest addition to the GX-range combines all the best of connectivity, redefining smart power solutions in every way
Victron M8 Circular Connector Male/Female 3 Pole 2m, 2 Pack.
M8 circular connector Male/Female 3 pole cable.
Features:
- 2 metres.
- Contains 2 circular connectors.
2 x Victron RJ45 UTP Cable 0.9m.
A cable to connect Digital Multi Control, Phoenix Inverter Control, Interface MK3-USB, VE.Bus connections between multiple VE.Bus devices and to make VE.Bus and VE.Can connections to a GX device.
Victron Interface MK3-USB – VE.Bus to USB.
The MK3-USB allows the products to connect to a computer for configuration and firmware updates.
Compatable with:
- Multi
- MultiGrid
- MultiPlus
- MultiPlus-II
- Quattro
- Inverter/Charger settings in ECOmulti
- EasySolar
- EasyPlus
- Inverters with a VE.Bus communication port.
Reviews
There are no reviews yet.